A leaning fence post is one of the most common fencing problems in UK gardens, and it rarely gets better on its own. Once a post starts to tilt, the wind has more leverage against it every time it blows, the panels either side start to twist, and a small lean can turn into a section of fence on the ground after a stormy night.

The short answer: the right fix depends on why the post is leaning. If the post is sound but has moved in the ground, it can usually be dug out around the base, pushed back upright, braced and reset in fresh Postmix. If a timber post has rotted at ground level, it needs replacing, or supporting with a concrete repair spur. If the post was never set deep enough, it needs resetting deeper, often with a longer post.

This guide explains how to work out what is causing the lean, the fix for each cause, and how to stop it happening again.

Quick Guide: Cause and Fix

Scroll →
What you find Likely cause Usual fix
Post and concrete lump tilt together Shallow hole, too little concrete or soft ground Dig out, straighten, brace and reset deeper in fresh Postmix
Timber post soft or snapped at ground level Rot where the timber meets the ground Replace the post, or fit a concrete repair spur
Post rocks inside its concrete Post has worked loose, often from wind Break out the old concrete and reset the post
Concrete post cracked or broken Impact or long-term stress Replace the post
Several posts in a row leaning Wind exposure, poor original installation or soil pressure Reset or replace the run, with stronger foundations

First: Make It Safe

A badly leaning fence can come down without warning, especially in strong wind. Before you start investigating:

  • Prop the fence with a timber batten or length of timber angled from the ground to the post, if it is leaning significantly.
  • Keep children and pets away from the leaning section.
  • Consider removing the panels either side if the fence is unstable and windy weather is coming. With slotted concrete posts, panels can usually be lifted out.
  • Talk to your neighbour if the fence is on a shared boundary or leaning into their garden.

Step 1: Work Out Why the Post Is Leaning

Fixing the lean without fixing the cause usually means the post leans again. Spend a few minutes diagnosing the problem first.

Push Test

Push the top of the post gently backwards and forwards and watch the base.

  • If the post and its concrete move together, the whole footing is loose in the ground.
  • If the post moves inside the concrete, the post has worked loose or rotted inside the footing.
  • If the post bends at ground level, a timber post is likely rotten or broken at that point.

Check a Timber Post for Rot

Scrape away soil from the base and press a screwdriver into the timber at and just below ground level. Sound timber resists. Rotten timber is soft, crumbly or wet, and the screwdriver sinks in easily. This is the most common failure point on timber posts.

Check a Concrete Post for Damage

Look for cracks running across the post, chipped or broken edges near ground level, or exposed reinforcement. A cracked concrete post cannot be reliably repaired and should be replaced.

Look at the Ground

Soft, waterlogged or recently disturbed ground, soil piled up against one side of the fence, or large tree roots nearby can all push or loosen a post.

Dig Down and Check the Depth

If you can, dig beside the post to see how deep it goes and how much concrete there is. For a 6ft fence, aim for around 2ft of post below ground. Many leaning posts turn out to have been set far shallower than that. See our guide to how deep a fence post should go.

Fix 1: Straighten and Reset a Sound Post

If the post itself is in good condition but has moved in the ground, it can usually be reset.

  1. Support the fence with a prop, or remove the panels either side if needed.
  2. Dig around the base of the post, down to the bottom of the existing footing.
  3. Break up or remove the old concrete if it is a small, shallow lump. If it is solid and deep but has simply tilted, it may need breaking out so the post can be reset properly.
  4. Deepen and widen the hole if it was too shallow, aiming for around 2ft below ground for a 6ft fence, with room for a solid collar of concrete all around the post.
  5. Add a few inches of gravel or hardcore in the bottom for drainage.
  6. Push the post back upright and check it with a spirit level on two faces.
  7. Brace it with timber battens screwed temporarily to the post and staked to the ground, so it cannot move while the concrete sets.
  8. Fill with Postmix, following the instructions on the bag, and recheck it is plumb.
  9. Slope the top of the concrete away from the post so rainwater runs off.
  10. Leave the braces in place until the concrete has fully set, then refit the panels.

Our working rule is 2 × 20kg bags of Postmix per standard post, and 3 bags for gate posts and posts in exposed or windy gardens. When resetting a post that has already failed, it is often worth using the extra bag. You can buy Postmix from our post concrete range.

What If the Post Is Too Short to Go Deeper?

If the post cannot be set deeper without losing height above ground, replace it with a longer post. For a fence finishing at around 6ft, that is normally an 8ft post, or a 9ft post if there is a gravel board under a 6ft panel. See our guide to what size fence post you need for a 6ft fence.

Fix 2: Repair a Timber Post Rotted at Ground Level

If a timber post has rotted where it meets the ground, straightening it will not help, because the timber at the base has lost its strength. You have two options.

Option A: Fit a Concrete Repair Spur

A concrete repair spur is a short concrete post set in the ground alongside the existing timber post and bolted to it. The spur takes over the job of the rotten section at ground level, while the sound upper part of the timber post continues to hold the panels.

A repair spur is a good option when:

  • The rot is limited to the section at and just below ground level.
  • The rest of the post above ground is still sound.
  • The panels either side are in reasonable condition.

To fit one, cut away or dig out the rotten base of the timber post if it is in the way, dig a hole for the spur tight against the post, set the spur in Postmix with the post pulled upright, and bolt the two together through the spur's pre-formed holes once it is positioned.

Option B: Replace the Post

If the rot extends well above ground, the post is split, or several posts are failing, replacing the post is the better long-term repair. Remove the panels either side, dig out the old post and its concrete, and set a new post to the correct depth with fresh Postmix. You can choose a replacement in our wooden fence posts range.

If you are replacing several timber posts, it may be worth considering a switch to concrete or steel posts that do not rot. Our guide to concrete vs timber fence posts compares the options.

Fix 3: Replace a Cracked or Broken Concrete Post

A cracked concrete post should be replaced rather than patched. With a slotted system, this is usually straightforward:

  1. Lift out the panels and gravel boards on either side.
  2. Dig out the old post and as much of its concrete as needed to set the new one.
  3. Set a new post of the same type and length: intermediate, end or corner, so the slots line up.
  4. Refit the gravel boards and panels before the Postmix sets, so the spacing is exactly right.
  5. Brace and leave until the concrete has fully set.

Make sure you order the right post shape for the position. You can see the options in our intermediate slotted posts, end slotted posts and corner slotted posts ranges, or browse all concrete fence posts.

Fix 4: A Whole Run Is Leaning

If several posts along a run are leaning in the same direction, the problem is usually the original installation or the conditions rather than one bad post. Common causes are:

  • Posts set too shallow or with too little concrete.
  • A full-height solid fence in an exposed, windy spot.
  • Soil or planting built up against one side of the fence.
  • Timber posts reaching the end of their life at the same time.

Resetting one post at a time can work, but when most of the run is affected, rebuilding the run with correctly set posts is often the more reliable fix. If soil is pushing on the fence, deal with that first, since a fence is not designed to act as a retaining wall.

Leaning Gate Posts

Gate posts carry far more sideways load than fence posts, so they are one of the most common posts to lean. A leaning gate post usually shows up as a gate that drags on the ground or no longer latches.

Gate posts should be set deeper than standard fence posts where possible, with 3 bags of Postmix per hole, and use a post suited to the weight of the gate. If a gate post keeps leaning, resetting it with more depth and concrete, or replacing it with a heavier post from our gate posts range, is usually the answer.

Can You Straighten a Fence Post Without Digging?

Sometimes a slightly leaning post can be pulled upright and held with a brace or angled support, but this rarely fixes the underlying problem. If the footing is loose, the post is rotten, or the post is too shallow, it will usually lean again. For a lasting repair, dig down and fix the cause.

How to Stop Fence Posts Leaning Again

  • Set posts deep enough: around 2ft below ground for a 6ft fence.
  • Use enough Postmix: 2 bags per standard post, 3 for gate posts and exposed sites.
  • Make holes wide enough for a solid collar of concrete all around the post.
  • Drain the base: put gravel or hardcore in the bottom of the hole.
  • Shape the concrete to shed water away from the post.
  • Use gravel boards to keep panels off the soil. See our guide to whether you need a gravel board.
  • Keep soil and heavy planting from building up against the fence.
  • Choose the right panel for exposed sites. Our Heavy Duty Closeboard Fence Panels use larger 75 × 32mm back rails.
  • Check the fence once a year, especially after winter storms, so small problems are caught early.

What You Might Need for the Repair

  • Spade, post-hole spade or auger, and a digging bar for old concrete.
  • Spirit level.
  • Timber battens and screws for bracing.
  • Gravel or hardcore for drainage.
  • Postmix.
  • A replacement post or concrete repair spur, if needed.
  • Suitable fixings from our screws, nails and fixings range.

So, How Do You Fix a Leaning Fence Post?

Find the cause first. If the post is sound but has moved, dig it out, straighten it, brace it and reset it deeper in fresh Postmix. If a timber post has rotted at ground level, fit a concrete repair spur or replace the post. If a concrete post is cracked, replace it. And if a whole run is leaning, look at the depth of the posts, the exposure and any soil pressure before rebuilding.

Whatever the fix, set the post around 2ft into the ground for a 6ft fence, use 2 bags of Postmix (3 for gate posts and exposed gardens), and give the concrete time to set before putting load back on the fence.

Frequently Asked Questions

Why is my fence post leaning?

The most common causes are a post set too shallow, too little concrete, soft or disturbed ground, wind loading over time, rot at the base of a timber post, or soil pushing against the fence.

Can I fix a leaning fence post without replacing it?

Yes, if the post itself is sound. Dig around the base, straighten it, brace it and reset it in fresh Postmix. A rotten timber post can sometimes be supported with a concrete repair spur instead of being replaced.

What is a concrete repair spur?

A short concrete post set in the ground beside a timber post and bolted to it, so it takes over at ground level where the timber has rotted.

How many bags of Postmix do I need to reset a fence post?

We normally recommend 2 × 20kg bags per standard post, and 3 bags for gate posts and posts in exposed or windy gardens. When resetting a post that has already failed, the extra bag is often worthwhile.

How long should I brace a reset fence post?

Leave the brace in place until the Postmix has fully set, following the setting time on the bag, before refitting panels or putting load on the post.

Can a cracked concrete fence post be repaired?

Not reliably. A cracked or broken concrete post should be replaced with a new post of the same type and length.

How deep should I reset a fence post?

For a 6ft fence, aim for around 2ft below ground, with more for gate posts and exposed gardens.

Why does my gate post keep leaning?

Gate posts carry constant sideways load. They need extra depth, 3 bags of Postmix and a post suited to the weight of the gate.

Is a leaning fence dangerous?

It can be. A badly leaning fence can fall in strong wind. Prop it, keep people and pets away, and consider removing panels until it is repaired.

Should I replace all my fence posts if one is leaning?

Not necessarily. If only one post has failed, fix that one. If several posts are leaning or rotting, it may be more reliable to rebuild the run.